Design your own court

A Guide to Tennis Court Maintenance

Tennis, one of the popular Olympic sports is played at all levels of society. The sport can be enjoyed at all ages and the match is intended to be continuous. If you own a tennis court you are responsible for its upkeep. If tennis court maintenance tasks are new to you then it might seem complicated and laborious. However, with the right tools and guidance you can accomplish your goal of tennis court maintenance.


If it is your first tennis court maintenance program, be careful to buy products from a renowned retailer. Remember not to compromise on the quality of the products. A few products such as tennis court paint is a good quality and non-slip surface coating for sporting entertaining areas. The court is a balanced formula of UV resistant oxide pigments, sturdy adhesion acrylic resins, fungicides and selected reinforcing filler.

Tennis Court Maintenance

Steps to maintain a tennis court:

Apply the following steps to maintain your tennis court as desired:

Tennis Court Maintenance Step One: Cleaning the court

The first step includes a thorough cleaning of the court surface. Most of the surface can be cleaned with a push-broom or blower. However, areas affected with mildew and algae should be cleaned with a bleach and water solution (ideally 1 part of bleach and 2 parts of water). The rinse solution will not harm any surrounding landscape. In case if the majority of the surface is covered with such fungus growth, you must use a power washer.


Tennis Court Maintenance Step Two: Remove any sort of vegetation growth on the court surface

It is natural that sometimes grass and weeds creep through the fence onto the court surface. In such cases, use a weed-eater or any similar tools to cut the vegetation growth. However, if vegetation grows up through the court, you will have to cut that area and as close to the vegetation as possible. Immediately apply a sterilant and patch the hole.

Tennis Court Maintenance Step Three: Check the court for any standing water

As soon as you notice water standing on the court for a long time after the rain, fill those areas to reduce ponding. This is vital as standing water invariably degrade the court and is responsible for the growth of mildew or fungi. Therefore, simulate the rain through spraying of water horizontally in order to push water out of the low areas. This will give you an accurate idea for the patching required. You should continue this task until you see the water beginning to run off.

Tennis Court Maintenance

Tennis Court Maintenance Step Four: Patch the tennis court

Measure the width of each patch by using a tape measure and record the measurement on your diagram. These measurements aid in determining the number and length of straightedges required for patching. The patch mix should be lump free and should have the consistency of a thick solution. Do not add excess water especially when the mix begins to set. If it is too thick to use, do not use it and instead make a new batch. Allow the patch to dry overnight. Blow off any loose particles created by dirt or stones. It is a good practice to flood the tennis court once again after the patching is complete. Patch any areas which have standing water.

Tennis Court Maintenance Crack Repair


Tennis Court Maintenance Step Five: Repair the crack:

Clean out the crack by using pressure-washer. Pressure washing is also considered as the best method to clean dirt and debris in the cracks.Check for any other organic matter and apply vegetation sterilant to remove grass or weeds. Make sure you clean the crack to a depth of 1 inch.Tennis court crack repair is an important part of the court maintenance.

Tennis Court Maintenance Power Washing

Tennis Court Maintenance Step Six: Prepare the court for coating:

After the application of patching and coating walk the entire court with a floor scraper to scrape up any smears or drips left on the court? Once scraping is finished, blow all of the scraping and remaining debris off the court before proceeding to the next step.

Tennis Court Maintenance Step Seven: Apply inbound and outbound tennis court color coating:

Apply the tennis court painting first in the inbound area by applying masking paper around the perimeter outside of the inbounds area. Painting the outbound area includes a few steps such as planning the start and ending points and spotting the pails of coating or placing the pails around the out-of-bounds. Once you finish painting the inbound and outbound do not forget to paint the tennis court border.

Well the maintenance methods might look too difficult for a novice but practice makes things perfect.

Leave a Reply

4 Comment threads
2 Thread replies
Most reacted comment
Hottest comment thread
5 Comment authors
designerShaylee PackerPaul GoldGarypaul Recent comment authors
newest oldest most voted
Notify of
Ben Johnson
Ben Johnson

I have a tennis court that was resurfaced a year ago by a company out of Georgia. I live in Jacksonville, FL , but the company in Georgia gave me a price that was a little bit lower than the companies in Florida. It seems that many of the cracks that were repaired and painted over are now showing back up in the same places. Is this normal? I am a bit frustrated because I feel like I just spent a good deal of money to restore my tennis court and now it looks like it did before. Is there… Read more »


the best way to keep courts from cracking is to apply a fiberglass membrane prior to the resurfacing process. Many of the tennis courts that we used fiberglass membrane to resurface courts in miami, west palm beach all the way to orlando and have had great success with keeping the crack return down to a minimum. Please visit our website at for more detailed information about hard court repair and resurfacing.


I have a har tru bocce court that I just completed will the surface ever get hard or does it always stay soft

Shaylee Packer
Shaylee Packer

I have noticed that there is some pooling that happens on my court after we get a good amount of rain. As you mentioned, it is important to fill those holes, so that it doesn’t cause damage to the court. Is this something that I can do myself, or do I need to hire I company to complete that?



typically if a court is holding less than a usa nickel after 1 hour of drying time it will dry on its own and nothing needs to be done. If it does not I would recommend calling us for a free estimate.

Quick quote